370W Circular Saw Blade 80-700mm Grinder Sharpener Machine Chainsaw Slideable
Introduction:
The machine is designed for sharpening various kinds of carbide tipped saw blades from size 80mm to 700mm. It’s also suitable to grinde other material, such as plastic, wood, aluminum alloy for different purpose like furniture manufacturing, decoration etc. Its fascia can support the teeth of saw blades and other parts in order to prevent jumping and improve grinding quality. This item can shapen all the round saw blade, such as Skil saw. It adopts multi angle of swing, three dimensional slide structures to be in adaptation to the grinding of hard alloy saw blades with many specifications and purposes, which enables the grinding mill to maintain high accuracy and easy operation on any condition.
Circular carbide saw blade are widely used for cutting aluminum, wood and plastic materials. MF-126 type grinding machine is used for sharpening many sizes and types circular carbide saw blade. If you change the sanding wheel it can also sharp other common saw blade. It is a necessary assistant machine for cutting aluminum, wood and plastic materials.
Method of operation:
First, loosing the fascia, then adjust the angle of grinding blade and fasten.
Second, adjusting of center axle.
Rotating the center axle to the grinding blade.
Pushing the center axle to the right.
Installing the saw blade ,rotate the wheel and decide the position of grinding surface saw teeth.
Rotating the rotation table to ensure the angle of grinding blade.
The cross angle between the grinding surface and work surface is about 5.
Third, adjusting of positioning assembly.
Adjusting the saw blade to the best grinding position, rotating the positioning frame and fascia.
Adjusting positioning pin to the proper base of saw teeth and leave gap of grinding quantity, fasten the fixed screw.
Fourth, adjusting the center axle to the same gap of grinding quantity to the right.
Last, when all the parts are fastened, the saw blade supported with hand will be grinded.
Safety remarks:
Should match the standard voltage; We must strictly take a good ground, install leakage circuit breakers.
The machine should be set in a dry, clean, steady and parallel place.
Release the round plat and then adjust the saw blade angle.
Check all parts that need locks before operation.
After the machine runs well then you can start the work.
Take off the electricity after work finishing.
Inform the factory before you change the machines.
1.base
2.box body
3.end cover
4.rotatary base
5.rotary table base
6.rotary table
7.slide base
8.slide disc
9.table
10.guide nut base
11.guide screw
12.slide block
13.frame
14.board
15.positioning board
16.safe cover
17.press board
18.adjusting bolt
19.upright post
20.long bolt
21.short bolt
22.long handle
23.short handle
24.positioning pin
25.mat cover
26.diamond wheel
27.cover
28.motor
29.rear stuck disc
30.fore stuck disc
31.big pin
32.small pin
33.hand wheel
34.round handle
35.turret handle
36.earth foot
37.adjusting bolt base
38.fastening handle
39.switch
40.screw
41.lirnit pin
42.washe
43.cover
Feature
The machine structure is strong and it can work on max diameter φ700mm.
The specially equipped motor has a very good running speed which can have a very good co-operation with the diamond sanding wheel.
The direction of the sharpening should be paralleled with the diamond sanding wheel, it is better for grinding the back teeth face.
This machine is designed for sharpening various kinds of carbide tipped saw blades from size 80mm to 700mm.
Also suitable to grind other material such as plastic, wood, aluminum alloy for different purpose like furniture manufacturing, decoration etc.
Steel chassis construction.
Grinding wheel angle control with large aluminum knob.
Will hold each blade head position by a position lock.
Extra 2 blade hole adapter.
X axis feed wheel, stable and very sharp grinding.
Rotary angle mark.
Specifications
Power: 370 W
Voltage: 220V
Running Speed: 3400 RPM
Adjusting Angle Of The Wheel: ±20°
Handle Turning Angle: 30 Degrees From Left And 45 Degrees From Right
Working Diameter: 80 – 700 mm
Grinding Wheel Size: 4.92″ / 125 mm
Bore Size Of Grinding Wheel: 1.26″ / 32 mm
Sanding Wheel Dimensions: 4.92″
x
0.39″
x
1.26″
x
0.2″
x
0.08″ / 125
x
10
x
32 x 5 x 2 mm
Net Weight: 66.14 lbs / 30 kg
Product Dimension: 30.3″
x
16.93″
x
11.81″ / 770
x
430
x
300 mm
Package Dimension: 16.93″
x
16.93″
x
13.58″ / 430
x
430
x
345 mm
Package Content:
ORDERS
NAME
DESCRIPTION
QT
1
Main Machine
1 Set
2
Sanding Wheel
φ125*10*32*5*2mm
1Tablet
3
Saw Centering
φ22、φ30、φ25
Each 1 Set
4
Saw Centering
φ40、φ25.4
Each 1 Set
5
Allen Wrench
5mm、
Each 1 Set
6
Cross
4*100
1Set
7
Open-end Wrench
12*14
1Set
8
Manual
1
9
Certificate
1
10
Packing List
1